Skip to content

Ulark5 · PTI line management

Every instrument on the line. One system.

Ulark5 drives the measurement equipment on a vehicle inspection line, records what each test produced, and delivers the result to the state register — whatever make the instruments are.

  1. 01 Registration
  2. 02 Queue
  3. 03 Measurement
  4. 04 Visual check
  5. 05 Record
  6. 06 Register
Instruments supported
45 Instruments supported
Equipment manufacturers
23 Equipment manufacturers
Measured parameters
12 Measured parameters
National registers
2 National registers

The system

Instruments in. Filed result out.

Five kinds of instrument, one unit, two applications, one archive and the state register. Everything else on this site is detail underneath this diagram.

Ulark system architectureMeasurement instruments connect over wired industrial interfaces to the Ulark5 unit. The unit drives a handheld application over Bluetooth and a station application over the local network. Both write to a central archive, which submits completed inspections to the state register.On the lineBrake benchGas analyserOpacimeterHeadlight testerOBDwired interfacesUlark5Line control unit16 ports · Linux · offline capableBluetoothNetworkDVS.MOBILEHandheld, atthe vehicleDVS.WEBStation, atthe deskCentral archiveEvery measurement, retrievableReports generated in PDFsubmissionState registerResults in, vehicle data out
Instruments keep their own protocols. Everything after the unit speaks one.

What it is

A device, not another computer.

Ulark5 is an industrial unit built on the USS.EYE PTI Business subsystem. It sits on the line, speaks to the benches and analysers already installed, and collects inspection data as the work happens — rather than after it, from a notepad.

Every position works to the same procedure and reports into the same record, so an inspection can be reconstructed afterwards: what was measured, on which instrument, in what order, by whom.

Runs on
Linux
Internet
Not required
Lines per system
Unlimited
Interfaces
6 wired types

On the line

From the gate to the register.

Six steps, the same on every position. Select one to see what the system is doing at that point.

Step 01 of 06

Registration

The vehicle is registered at the entry lane, at reception or through online booking. If it has been inspected before, the registration number is enough.

Inspection lane layoutA vehicle enters at registration, stops in turn at the brake, emissions, lights and visual inspection positions, and leaves once the report is printed and the result filed.EntryRegistration1BrakesRoller bench2EmissionsGas · opacity · OBD3LightsIntensity · alignment4VisualGuided checklistExitReport filed
The inspector carries one handheld along the lane. Every position reports into the same record.

What it does

Six things that change how a line runs.

Each one removes a specific piece of friction that inspection stations put up with because the equipment was never designed to work together.

  • 01

    Manages any manufacturer’s equipment

    The instruments on the line keep working as they are. Replacing one later is a driver change, not a rebuild of the station.

  • 02

    Fast, centralised data collection

    Readings leave the instrument as they are produced and land in one database, with nothing re-typed in between.

  • 03

    Continuous and secure transfer

    The line keeps running if a link drops; data is carried through and reconciled rather than lost.

  • 04

    Measurement equipment management

    The handheld drives the bench directly — start a test, read the result, move on — instead of walking to each console.

  • 05

    Uniform procedures

    Every inspector follows the same sequence on the same screens, which is what makes results comparable between shifts and between stations.

  • 06

    Full internal control

    The record shows who performed which step and when, so quality checks are a query rather than an investigation.

Supported equipment

45 instruments. 23 manufacturers. One interface.

Not a compatibility promise — a driver list. Every make and model below is driven by the product today.

Gas analysers

7

Petrol exhaust: CO, CO₂, HC, O₂, lambda

  • MAHA · MGT 5
  • Bosch · BEA 050 / 150
  • Bosch · BEA 460 MUX
  • SAXON Junkalor · Infralyt CL
  • +3 more

Opacimeters

10

Diesel exhaust opacity and engine speed

  • MAHA · MDO 2
  • AVL DiTEST · DiSmoke 480
  • SAXON Junkalor · Opacilyt 1020
  • SAXON Junkalor · Opacilyt 1030
  • +6 more

Combined analysers

5

Gas and opacity in one instrument

  • Sun Diagnostics · DGA 1500
  • Bosch · RTM 430
  • Bosch · BEA 050 ALL
  • AVL DiTEST · AUX 2000
  • +1 more

Brake testers

17

Roller and plate benches, force per wheel

  • MAHA · IW2 / IW4 / IW7
  • MAHA · IW FX KDS
  • MAHA · LON Bas
  • MAHA · LON IW
  • +13 more

Headlight testers

5

Intensity and alignment

  • MAHA · LITE 3
  • CAPELEC · CAP 2500 (Bluetooth)
  • CAPELEC · CAP 2500 (Wi-Fi)
  • L.E.T. Automotive · Luminoscope PLA 25
  • +1 more

Cameras

1

Visual evidence tied to the measurement record

  • MOBOTIX · M22 / Q24 Hemispheric
  • MAHA
  • Bosch
  • SAXON Junkalor
  • Tecnotest
  • Hermann
  • Texa
  • AVL DiTEST
  • CAPELEC
  • Opus Prodox
  • Paltest
  • Sun Diagnostics
  • Beissbarth
  • Sherpa Autodiagnostik
  • Otto Nußbaum
  • Snap-on Equipment
  • BM Autoteknik
  • ATT
  • Hofmann
  • HANNI
  • JeamBeam
  • L.E.T. Automotive
  • Technoliux
  • MOBOTIX

Two applications

One at the desk. One in your hand.

The station and the line need different screens. They share one record.

DVS.WEB

Station application

The desk side of the station: queue, vehicle records, results, reports, staff, permissions and station configuration.

  • Queue and line flow across every position
  • Vehicle history and measurement archive
  • Report generation and printing
  • Staff accounts and permission levels
  • Station and equipment configuration

DVS.MOBILE

Handheld application

What the inspector actually holds. Drives the benches, walks through the inspection guide and captures visual findings at the vehicle.

  • Controls the connected test equipment
  • Guided visual inspection points
  • Live measurement readout at the vehicle
  • Works on the line, not at a desk

What it removes

The five things stations stop living with.

None of these are software problems. They are what happens when instruments from different decades and different manufacturers end up on one line.

  • 01 A different console and a different interface for every brand of equipment
  • 02 A separate computer added beside each instrument
  • 03 Time lost carrying results from one system to another by hand
  • 04 Mismatched screens that make procedures differ between positions
  • 05 Weak internal control over how an inspection was actually performed

Where results go

An inspection is not finished until it is filed.

The system carries the completed result to the state register, and hands the rest on to whatever the company already runs.

  • State register

    Submission and lookup

    Completed inspection results are submitted to the state vehicle inspection register, and vehicle data is retrieved from it at registration. Each country runs its own register, so the connection — including the payment handling a station needs at the counter — is configured per installation.

  • Google Workspace

    Documents and scheduling

    The system links to Drive for storing data, Docs for generating reports, Sites for publishing information and Calendar for scheduling.

  • Station systems

    Onward transfer

    Processed information is archived and handed on to whatever the company already runs for accounting and resource planning.

The unit

Ulark5

An industrial device, not a PC in a cabinet. Sixteen ports, relay control and six wired interface types, running Linux with no dependency on an internet connection.

Power
12–30 V, 2 A
Relays
8 NO / 8 NC
Interfaces
RS232, RS485, Ethernet, CAN, USB, LON
Connection ports
16, with hardware modules connectable
Mobile
GSM 3G module
Wi-Fi
Optional adapter, via Ethernet or USB
Firmware
Ulark5
Operating system
Linux

Universal monitoring system

Ulark is one member of USS.EYE.

Ulark is the inspection-line member of a wider family. USS.EYE receives and processes data from sensors, measurement devices and control equipment, archives the result, hands it on to other systems and controls the connected equipment centrally — without depending on the manufacturer or type of that equipment.

  • LARK

    This product

    PTI Business

    The subsystem Ulark5 runs. Automates periodic technical inspection: the queue, the equipment, the procedure and the record of what each measurement produced.

  • TAURUS

    Company operations

    Resource Management

    Plans and accounts for the work itself — which jobs are running, what they consume, and what the company has left to commit.

  • OWL

    Visual evidence

    Image Processing

    Ties recorded images to the measurement output, so a stored result can be looked at as well as read.

DVS. DVS combines the measuring tools on the line into a single controllable set, and can be changed quickly when equipment is swapped or requirements are updated. It is the reason a station can replace one manufacturer’s bench with another and keep every screen, procedure and report exactly as it was.

Next step

Tell us what is on your line.

Send the makes and models of the benches and analysers you run. We will tell you which are already supported and what the rest would take.